Hi.
My step daughter's 1998 Megan 1.6e has been causing problems recently. Firstly the head gasket started leaking (plainly evident due to water being squirted out of no. 4 cylinder with plugs removed). The gasket was replaced and the head checked for alignment, the cam belt was changed at the same time since we didn't know when that had last been done. When trying to vent the cooling system via the extremely fragile bleed screw on the heater hose, it broke off (seems very common - at the breakers almost every one of them was broken). Replacing it didn't help to get heat back in the heater.
After only a very short period, the car started loosing a lot of water - which was quickly traced to the water pump - since it had started making aweful noises. Off with the cambelt again, new waterpump fitted, car now running normally, but no heat from heater. All attempts to flush through the heater have been to no avail. The now runs properly, looses no water, but no amount of bleeding can get any heat out of the heater.
Any ideas? Is there a hot water valve in the heater matrix circuit or is there supposed to be hot water circulating in it all the time? The haynes BOL is useless on this car.
Its bl***y cold over here in Sweden at the moment (-13 C in southerly Malmö) so some heat would be greatly appreciated!
//Nisk
Megan heater not heating
-
NiSk
- Posts: 1422
- Joined: 24 Jan 2002, 20:11
- x 1
Megan heater not heating
'85 BX 16TRS, '91 XM injection 241,000 km (company car), '93 XM TD12 (515,000 km), '98 XM 2.5TD Break (320,000 km)
-
spider
- Posts: 3949
- Joined: 05 Jan 2010, 14:28
- x 77
If the heater hoses (both in and out of the matrix) are not both really hot, then I'd guess the matrix is blocked internally 
If they are the same as most PSA stuff: (no actual water valve) and both hoses are hot, its probably going to be a control cable / flap that's broken in the heater box up inside the dash somewhere.
I'm sorry that's not a lot of help, I'm not really familiar with these but hopefully its a bit of a start.
If they are the same as most PSA stuff: (no actual water valve) and both hoses are hot, its probably going to be a control cable / flap that's broken in the heater box up inside the dash somewhere.
I'm sorry that's not a lot of help, I'm not really familiar with these but hopefully its a bit of a start.
Andy.
91 205D-Turbo, gone but still missed
02 106D, TUD5B, gone but not really missed apart from the MPG
91 205D-Turbo, gone but still missed
02 106D, TUD5B, gone but not really missed apart from the MPG
-
AndersDK
- Posts: 6060
- Joined: 21 Feb 2003, 04:56
- x 1
Hi NiSk -
Long time no see
At least its not that cold as you had a week ago
My bet is that your garage did not properly bleed the cooling system.
Its the standard issue.
And many newer cars are in fact pretty hard to bleed properly.
Use the old trick with a bottomless bottle in the coolant filler neck to create a coolant surface that really is situated well above the level of any part of the cooling system.
Otherwise I can only back up on Spiders thoughts.
Good luck - and see ya around 8)
Long time no see
At least its not that cold as you had a week ago
My bet is that your garage did not properly bleed the cooling system.
Its the standard issue.
And many newer cars are in fact pretty hard to bleed properly.
Use the old trick with a bottomless bottle in the coolant filler neck to create a coolant surface that really is situated well above the level of any part of the cooling system.
Otherwise I can only back up on Spiders thoughts.
Good luck - and see ya around 8)
Anders (DK) - '90 BX16Image