After installing a few updates from the initial install of 7.02 the software now won’t close. After each update (am now on 7.57) i was able to close Diagbox ok after it installed the “internet updates”, but then after restarting the laptop & then opening Diagbox again - when I try to close it just says “Closing of the application in progress, please wait” .... & half an hour later it's still trying to close.
I thought that perhaps any updates would cure this but it appears thats not the case. I have a Rev C full chip interface & Win7. Doesn't make any difference if I have the interface connected or not.
Only way to close is with task manager. I take it it's not safe to use with the car if its not shutting down properly ?
Thanks
Diagbox not closing
Moderator: RichardW
Re: Diagbox not closing
Hmm
I have yet to figure out how to update mine. I have a phobia about letting it connect to the net.
Now I'm worried about messing with it at all. It works at the moment...
I have yet to figure out how to update mine. I have a phobia about letting it connect to the net.
Now I'm worried about messing with it at all. It works at the moment...
Sparksie
2000 Xantia 1.9TurboD
2000 Xantia 1.9TurboD
- GiveMeABreak
- Forum Admin Team
- Posts: 36996
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5645
Re: Diagbox not closing
These aren't internet updates - it's just what it says on the screen! As long as you have your network adapter enabled , but no live connection to the net you are fine.
Max - make sure that windows update is not getting re-enabled after startup and anti virus software - that will interfere with updates. Disable the services for now until everything is installed.
Max - make sure that windows update is not getting re-enabled after startup and anti virus software - that will interfere with updates. Disable the services for now until everything is installed.
Please Don't PM Me For Technical Help
Marc
Marc
-
- (Donor 2017)
- Posts: 69
- Joined: 21 Aug 2017, 14:02
- Location: Bournemouth
- My Cars: 09' Peugeot 207 1.4 Vti
- x 5
Re: Diagbox not closing
Cheers Marc, had to turn the firewall off as well as Windows update & now it closes fine. Phew.
- GiveMeABreak
- Forum Admin Team
- Posts: 36996
- Joined: 15 Sep 2015, 19:38
- Location: West Wales
- My Cars: C3 Aircross SUV HDi Flair Peperoncino Red (The Chili Hornet)
C5 X7 2.0 HDi Exclusive Mativoire Beige (The Golden Hornet)
C3 1.6 HDi Exclusive Aluminium Grey (The Silver Hornet)
C5 MK II 2.0 HDi Exclusive Obsidian Black
C5 MK I 2.0 HDi SX Wicked Red
Xantia S2 2.0 HDi SX Hermes Red
C15 Romahome White
XM 2.0 Turbo Prestige Emerald Green Pearlescent
XM 2.0 Turbo Prestige Polar White
XM 2.0 SX Polar White
CX 20 Polar White
GS 1220 Geranium Red
CX 2.4 Prestige C-Matic Nevada Beige
GS 1000 Cedreat Yellow - x 5645
Re: Diagbox not closing
If you don’t allow the firewall requests it may interfere with future sessions, so important to allow all these through Max.
Please Don't PM Me For Technical Help
Marc
Marc
-
- (Donor 2017)
- Posts: 69
- Joined: 21 Aug 2017, 14:02
- Location: Bournemouth
- My Cars: 09' Peugeot 207 1.4 Vti
- x 5
Re: Diagbox not closing
Funny because I did allow all connections as & when it prompted & the updates installed fine it was just closing it that was the problem. The only way to get it to close was turning it off completely. Maybe just a glitch on my particular machine. Thx