The offside ABS toothed ring on the offside front drive shaft on my Xantia HDI 90 has split and sprung apart, leaving a gap. So the ABS thinks there is wheel slip and keeps kicking in.
Has anyone ever changed one of these, if so what is involved. It looks like it would be an interference sliding fit. The rings are available on ebay.
ABS TOOTHED DRIVESHAFT RING ON XANTIA?
Moderator: RichardW
ABS TOOTHED DRIVESHAFT RING ON XANTIA?
Now using '00 Xantia LX HDI, pov spec
My past Citroens :-
'00 Xantia SX HDI, now dead due to accident
'99 Xantia HDI 110 Exclusive, RIP
'97 Xantia TD SX
'96 Xantia TD LX
'96 ZX TD
'89 BX TD
'88 AX GT
'79 CX2400 Pallas (scrapped )
& a couple of Peugeots !
My past Citroens :-
'00 Xantia SX HDI, now dead due to accident
'99 Xantia HDI 110 Exclusive, RIP
'97 Xantia TD SX
'96 Xantia TD LX
'96 ZX TD
'89 BX TD
'88 AX GT
'79 CX2400 Pallas (scrapped )
& a couple of Peugeots !
-
- Forum Treasurer
- Posts: 10871
- Joined: 07 Aug 2002, 17:12
- Location: United Kingdom
- My Cars: MK2 '17 C4GP 1.6 BlueHDi 120
'13 3008 1.6 HDi GripControl - x 996
Re: ABS TOOTHED DRIVESHAFT RING ON XANTIA?
Easy enough: https://www.frenchcarforum.co.uk/forum/ ... 8&start=16
I'd give JandR CV joints a try - their parts are pretty good value.
I'd give JandR CV joints a try - their parts are pretty good value.
Richard W
-
- Posts: 251
- Joined: 18 Mar 2008, 16:56
- Location: Wakefield
- My Cars: Peugeot 806
Citroen C3 1.4 Hdi - x 4
Re: ABS TOOTHED DRIVESHAFT RING ON XANTIA?
I've welded them back on before now, just a couple of spots required.
1998 1.9td Peugeot 806 (Red shed 2)
2004 Citroen C3 1.4HDi
2003 2.2 Pug 807, Gone and never again!
2004 Citroen C3 1.4HDi
2003 2.2 Pug 807, Gone and never again!
-
- Donor 2023
- Posts: 13743
- Joined: 01 Apr 2012, 09:47
- Location: Reading
- My Cars: C5 Mk2 VTX+ estate.
- x 3007
Re: ABS TOOTHED DRIVESHAFT RING ON XANTIA?
CitroJim and I sorted out the rings on my Xantia a few years ago. It was a bit of a palaver, as we had to get the hub nut undone, and then disconnect a strut (I cannot remember which bit) from the hub so we could move it out of the way, remove the ring, clean up the drive shaft, and then fit the new ring (which had been in the over for half an hour at 170C) and put everything back together. Then we had to do the same for the other side!
James
ex BX 1.9
ex Xantia 2.0HDi SX
ex Xantia 2.0HDi LX
Ex C5 2.0HDi VTR
Ex C5 2.0HDi VTR
C5 2.2HDi VTX+
Yes, I am paranoid, but am I paranoid ENOUGH?
Out amongst the stars, looking for a world of my own!
ex BX 1.9
ex Xantia 2.0HDi SX
ex Xantia 2.0HDi LX
Ex C5 2.0HDi VTR
Ex C5 2.0HDi VTR
C5 2.2HDi VTX+
Yes, I am paranoid, but am I paranoid ENOUGH?
Out amongst the stars, looking for a world of my own!
- CitroJim
- A very naughty boy
- Posts: 49620
- Joined: 30 Apr 2005, 23:33
- Location: Paggers
- My Cars: Bluebell the AX, Polly the C3 Picasso, Pix the Nissan Pixo, Propel the duathlon bike, TCR Pro the road bike and Fuji the TT bike...
- x 6182
- Contact:
Re: ABS TOOTHED DRIVESHAFT RING ON XANTIA?
Easier and cheaper than swapping a whole driveshaft though James and then there's the fun and satisfaction of doing it. After all, it's not often you use a cooker for car repairs
Jim
Runner, cyclist, time triallist, duathlete, Citroen AX fan and the CCC Citroenian 'From A to Z' Columnist...
Runner, cyclist, time triallist, duathlete, Citroen AX fan and the CCC Citroenian 'From A to Z' Columnist...