C5 Crankshaft pulley
Moderator: RichardW
- SaabC5
- Posts: 765
- Joined: 01 Aug 2011, 23:18
- Location: SW London
- My Cars: 09 C5 X7 2.0Hdi Exclusive
- x 1
C5 Crankshaft pulley
Can any Citroen boffins out there give me the torque setting for the dual mass crankshaft pulley on the 2.2 DW12TED4 please.
09 C5 X7 2.0Hdi Exclusive in Perla Nera black (the best colour)
Re: C5 Crankshaft pulley
pre tighten to 70Nm then 82 degrees +or- 5 degrees.
- SaabC5
- Posts: 765
- Joined: 01 Aug 2011, 23:18
- Location: SW London
- My Cars: 09 C5 X7 2.0Hdi Exclusive
- x 1
Re: C5 Crankshaft pulley
Thank you very much.
09 C5 X7 2.0Hdi Exclusive in Perla Nera black (the best colour)
-
- Posts: 116
- Joined: 15 Oct 2005, 16:44
- Location: Cumbria, CA21
- My Cars: '05 C4 2.0HDI Exclusive
'07 Lexus RX400h
Past:
'73 GS 1220 Club Estate (a good intro to hydraulics and rust)
'74 DS D Super 5 (Superb comfort and even more rust)
'?? Dyane (fun + rust)
'?? CX 2400 GTI (served me well)
'89 CX Safari 2.5 DTR turbo (aka "the hearse" an excellent family load lugger)
'97 XM 2.1TD (Reliable and economical) - x 2
Re: C5 Crankshaft pulley
Citroen DocBackup Repair Manual saysfor the DW12TED4 engine (under procedure B1EG1UP0 Removing - refitting : Timing belt : DW12TED4 TURBO DIESEL) :
"Coat the bolt (19) with LOCTITE FRENETANCH .
Fit :
Crankshaft pulley (21)
The tool [6]
The screw (19) with the washer (31), tighten to 4 ± 0,4 m.daN Finish with an angular tightening of 51° ± 5 °"
Tool [6] is the flywheel locking tool.
EDIT
For the later DW12TED4 FAP engine the following instruction applies:
"Coat the bolt (9) with LOCTITE FRENETANCH .
Fit :
The accessories drive pulley (10)
The bolt (9) with its washer
Tighten the screw (9) to 7 ± 0,7 m.daN Angular tightening A : 82 ± 3 ° " .
Take your pick! RP number would help to clarify.
"Coat the bolt (19) with LOCTITE FRENETANCH .
Fit :
Crankshaft pulley (21)
The tool [6]
The screw (19) with the washer (31), tighten to 4 ± 0,4 m.daN Finish with an angular tightening of 51° ± 5 °"
Tool [6] is the flywheel locking tool.
EDIT
For the later DW12TED4 FAP engine the following instruction applies:
"Coat the bolt (9) with LOCTITE FRENETANCH .
Fit :
The accessories drive pulley (10)
The bolt (9) with its washer
Tighten the screw (9) to 7 ± 0,7 m.daN Angular tightening A : 82 ± 3 ° " .
Take your pick! RP number would help to clarify.
Ken Hall
Re: C5 Crankshaft pulley
Never seen a 2.2HDi C5 without FAP...
I normally torque them to FT with an air gun
I normally torque them to FT with an air gun