Clic clip nightmare

This is the Forum for all your Citroen Technical Questions, Problems or Advice.

Moderator: RichardW

Post Reply
MikeT
Posts: 4809
Joined: 11 Jun 2007, 16:17
Location: Christchurch, Dorset. UK
My Cars: 2005 C5restyle 1.6HDI 16v 110hp VTR Estate
2008 C5 X7 1.6HDI VTR+ Saloon
x 231

Clic clip nightmare

Post by MikeT »

If you've read my posts, you'll know I need two new clic clips to refit the EGR pipe as I deformed the originals on removal.

According to service.citroen.com my car wasn't built with EGR system but I've tracked down the part number for the clips. 1628.3J (item 4 in the diag) which the stealers are asking £8+ for one :evil: Can I get them elsewhere for less?

Image

The new ones are revised and use an allen bolt & nut to make the seal which makes removal and refitting far easier.
jgra1
(Donor 2021)
Posts: 4625
Joined: 27 Nov 2005, 19:07
Location: Kent / Susssex
My Cars: 2010 C5 X7 2.0 hdi 160 exc auto
MG TF 135
Boxer II 2.2 camper conversion
BMW R1200RT
BMW K1300 R
Honda V F R 800 5thG / MT500 Armstrong
x 39

Post by jgra1 »

I thought you blanked this Mike? or am i getting confused?
MikeT
Posts: 4809
Joined: 11 Jun 2007, 16:17
Location: Christchurch, Dorset. UK
My Cars: 2005 C5restyle 1.6HDI 16v 110hp VTR Estate
2008 C5 X7 1.6HDI VTR+ Saloon
x 231

Post by MikeT »

You're right, I did fit blanking plates, but they're held in place by the original equipment.
jgra1
(Donor 2021)
Posts: 4625
Joined: 27 Nov 2005, 19:07
Location: Kent / Susssex
My Cars: 2010 C5 X7 2.0 hdi 160 exc auto
MG TF 135
Boxer II 2.2 camper conversion
BMW R1200RT
BMW K1300 R
Honda V F R 800 5thG / MT500 Armstrong
x 39

Post by jgra1 »

ahh of course!

sorry Mike

I may have two of 'em ?

Will try and look later
MikeT
Posts: 4809
Joined: 11 Jun 2007, 16:17
Location: Christchurch, Dorset. UK
My Cars: 2005 C5restyle 1.6HDI 16v 110hp VTR Estate
2008 C5 X7 1.6HDI VTR+ Saloon
x 231

Post by MikeT »

Thanks John. The other alternative is try and reform the old ones which has been unsuccessful so far.
citronut
Posts: 10937
Joined: 29 Apr 2005, 00:46
Location: United Kingdom east sussex
My Cars:
x 92

Post by citronut »

just but two jubile clips from the factors

regards malcolm
User avatar
Xaccers
Posts: 7654
Joined: 07 Feb 2007, 23:46
Location: Milling around Milton Keynes
My Cars:
x 184

Post by Xaccers »

citronut wrote:just but two jubile clips from the factors

regards malcolm
Don't think that would work as the cross section of the clip is C shaped to goe around the lip.
1.9TD+ SX Xantia Estate (Cassy) running on 100% veg
1.9TD SX Xantia Hatchback (Jenny) running on 100% veg for sale
Laguna II 2.0dCi Privilege (Monty)

DIY sphere tool
jgra1
(Donor 2021)
Posts: 4625
Joined: 27 Nov 2005, 19:07
Location: Kent / Susssex
My Cars: 2010 C5 X7 2.0 hdi 160 exc auto
MG TF 135
Boxer II 2.2 camper conversion
BMW R1200RT
BMW K1300 R
Honda V F R 800 5thG / MT500 Armstrong
x 39

Post by jgra1 »

Mike sorry it was too wild to venture out tonight :(

my setup is a bit extreme ...

Will try again tomorrow.
MikeT
Posts: 4809
Joined: 11 Jun 2007, 16:17
Location: Christchurch, Dorset. UK
My Cars: 2005 C5restyle 1.6HDI 16v 110hp VTR Estate
2008 C5 X7 1.6HDI VTR+ Saloon
x 231

Post by MikeT »

Thanks for the offer John. Malcolm's given me an idea of using a jubilee to close the clic clip and make the seal. :idea:
MikeT
Posts: 4809
Joined: 11 Jun 2007, 16:17
Location: Christchurch, Dorset. UK
My Cars: 2005 C5restyle 1.6HDI 16v 110hp VTR Estate
2008 C5 X7 1.6HDI VTR+ Saloon
x 231

Post by MikeT »

Nightmare over, the originals succumbed to patient bending, rebending and twisting to form a strong enough clasp. :twisted:
jgra1
(Donor 2021)
Posts: 4625
Joined: 27 Nov 2005, 19:07
Location: Kent / Susssex
My Cars: 2010 C5 X7 2.0 hdi 160 exc auto
MG TF 135
Boxer II 2.2 camper conversion
BMW R1200RT
BMW K1300 R
Honda V F R 800 5thG / MT500 Armstrong
x 39

Post by jgra1 »

:D
mmwain
Posts: 10
Joined: 07 May 2012, 21:37
Location:
My Cars:
x 3

Re: Clic clip nightmare

Post by mmwain »

I had a nightmare finding these clic clips so hope this helps someone! Loads of places advertising them on old web pages but when you get in touch don't actually have any and say the company making them has gone out of business. The good news is that I finally found someone else making them but under a different name - EzyClik-M. Managed to get some for under a pound each and they are not quite the same but close enough to not really notice the difference and to work with Clic clip pliers. Quality is just as good as the originals and they look miles better than worm drives or those giant spring things!
Having said that neither of the clips shown as item 4 in the image actually looks like a clic clip!
mmwain
Posts: 10
Joined: 07 May 2012, 21:37
Location:
My Cars:
x 3

Re: Clic clip nightmare

Post by mmwain »

I have a big box full of these so would be happy to sell some on if anyone else still can't get them.
Post Reply