Clip on driveshaft required.
Moderator: RichardW
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Clip on driveshaft required.
Sorry to be after more parts but I need a couple of the clips that locate the Rzeppa joint (on the front end of the drive shaft) against the splined end of the shaft to avoid it sliding in and out.
I got some from Simply Bearings who state 24 mm outside and 22 inside diameters but when they came they were 2mm thick so no good; does anyone know where I can get the proper ones - 1.5 mm thick - without a minimum order value or quantity?
TIA.
I got some from Simply Bearings who state 24 mm outside and 22 inside diameters but when they came they were 2mm thick so no good; does anyone know where I can get the proper ones - 1.5 mm thick - without a minimum order value or quantity?
TIA.
Last edited by uhn113x on 03 Apr 2017, 16:32, edited 1 time in total.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
Re: Clip on driveshaft required.
If you can't find any a toolmaker or engineer shop with a surface grinder should be able to adapt the ones you have for a few pounds.
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
I'll try that if all else fails, James, but I don't see how they'll do it as the clips are a round section, like wire.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
Re: Clip on driveshaft required.
They won't then, I assumed a square section.
-
- (Donor 2020)
- Posts: 7221
- Joined: 08 Jun 2011, 18:04
- Location: GL15***
- My Cars: 2006 C5 2.0 Litre HDI VTR Automatic Estate.(now sold on)
Currently Renault Zoe 2014 ZE - x 2520
Re: Clip on driveshaft required.
Man is, by nature, a lazy beast, he does not need twice encouraging to do nothing.
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
Thanks, I've emailed them.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
Unfortunately they don't have them, but I've spoken to these:
https://www.rotorclip.com/base_part_search.php and hopefully some will be arriving soon.
https://www.rotorclip.com/base_part_search.php and hopefully some will be arriving soon.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
Nope - they sent square section ones!
Surely someone else with a GSA will have the same problem?
Surely someone else with a GSA will have the same problem?
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
- Stonehopper
- Posts: 342
- Joined: 24 Feb 2012, 16:10
- Location: Shropshire
- My Cars: 1975 GS Pallas
1967 2cv AZAM
Previously;
1982 Acadiane
1990 BX TZD turbo
1982 2cv Charleston
1971 AK 250
1978 AK 400
1982 Ami 8 break
1971 Ami 8 break
1979 CX Familiale
1960 2cv AZL (Belgian built) - x 115
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
He's got none!
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
- Stonehopper
- Posts: 342
- Joined: 24 Feb 2012, 16:10
- Location: Shropshire
- My Cars: 1975 GS Pallas
1967 2cv AZAM
Previously;
1982 Acadiane
1990 BX TZD turbo
1982 2cv Charleston
1971 AK 250
1978 AK 400
1982 Ami 8 break
1971 Ami 8 break
1979 CX Familiale
1960 2cv AZL (Belgian built) - x 115
Re: Clip on driveshaft required.
Did he not suggest an alternative from another vehicle? (Possibly not)
Keith Would might have something from his aging stock, but he's not on the 'net. He lives near Kings Lynn. I'll PM his address and phone number in the event you don't have it.
Keith Would might have something from his aging stock, but he's not on the 'net. He lives near Kings Lynn. I'll PM his address and phone number in the event you don't have it.
Derek
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
Thanks very much for that, Derek.
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
-
- (Donor 2020)
- Posts: 7221
- Joined: 08 Jun 2011, 18:04
- Location: GL15***
- My Cars: 2006 C5 2.0 Litre HDI VTR Automatic Estate.(now sold on)
Currently Renault Zoe 2014 ZE - x 2520
Re: Clip on driveshaft required.
I'll bet Malcom would have had some..........................if Chris knew where to look.
Man is, by nature, a lazy beast, he does not need twice encouraging to do nothing.
- myglaren
- Forum Admin Team
- Posts: 25480
- Joined: 02 Mar 2008, 13:30
- Location: Washington
- My Cars: Mazda 6
Ooops.
Previously:
2009 Honda Civic :(
C5, C5, Xantia, BX, GS, Visa.
R4, R11TXE, R14, R30TX - x 4922
Re: Clip on driveshaft required.
Gibbo2286 wrote:I'll bet Malcom would have had some..........................if Chris knew where to look.
There's a thought!
If all else fails it may be worth a dig around there if Chris is amenable to it.
- uhn113x
- Posts: 1161
- Joined: 06 Jan 2004, 22:06
- Location: Near Leeds, United Kingdom
- My Cars: 1981 Dyane - on road all year round.
1982 GSA Pallas - on road April - September.
1997 ZX 1.9D Dimension. - x 1
Re: Clip on driveshaft required.
I'm still waiting for these:
https://www.yell.com/biz/hayley-group-p ... n-1486400/
but if that fails, who's Chris? Is he on here?
https://www.yell.com/biz/hayley-group-p ... n-1486400/
but if that fails, who's Chris? Is he on here?
Mike in West Yorks
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension
1982 GSA Pallas
1982 Dyane
1997 ZX Dimension