French Car Forum

Hello Everyone, I have a 2002 Boxer Motorhome and there are a few jobs mounting up, but to get the right parts it would be useful if I could find someone that is able to de-code the VIN .. I can't join the Peugeot service box as I am not a professional repair shop, does anyone have any ideas ?

Would be good to know ! Thanks in advance !! :)

I'm slowly working through all the faults on my 2008 207cc and I'm down to 1 non-engine fault.
But both the 'ABS/traction control' and the 'Radio or radiotelephone (radio part)' have 'ECU not recognised' next to them.
Both units are communicating just fine with Diagbox.
The radio has been upgraded from an RD4 to an RD45, but I'm not sure about the...

Please can anyone tell me if the primer bulb on a 20hdi should stay hard when pumped or go soft again trying to find out what gives low fuel pressure thanks

All my reversing sensors failed at the same time I think its unlikley they would all fail. Iv checked the fuse and the plug connection in the rear bumper all good.
But I cannot locate the ecu for the system, Iv been in the boot floor and rear lining. Anyone ? :roll: :roll:

So, it's a Peugeot Boxer 1.9 TD 1998 Autosleeper Pollensa motorhome, on 64000 miles, with bad idle and smoke. I've owned it since 2015, since when it's had regular oil, air and fuel filter changes and literally never missed a beat until Nov 2023 at around 63690 miles when lumpy idle and white/grey smoke began to be a problem, even when fully...

Seems two of the three front diesel injectors have a bit of a fuel leak as per pics (5U3G-9K546-AA)

I've tightened up the hold down bolts and line nuts but still get a bit of diesel leakage

The middle one is nice and clean, whilst the other two are brown all over , so hard to tell where the leak may be. No obvious seepage when running

My...

Hello everyone. I have a question about resetting the eolys additiv amount on the ECU. You see that the problem I have is that I don't have a diagbox or non other obd scanners that could pull this off. There fire I think I'm going to order one since my stealership asks 200eur for this in my opinion not complicated job. I have the error p1434 and...

It was ok but now putting water into the expansion bottle and it is pouring right out onto the ground seems to be the left hand side of the engine anyone e any ideas please ,thanks BTW its a 2011 model

Hi everyone, We've got a bit of an issue with our 206.

The engine had low compression, so swapped in a new engine, and she now starts and runs great again.
I also changed over the AL4 gearbox over to the new engine. I did drain a bit of oil from the gearbox, and refilled with that same oil after refitting. Because I did spill a a bit here and...

Hi

Car was running great on highway and then went into limp mode / cruise control error and MIL light

Diag is showing P0088 fuel pressure is higher that reference value 361 bar / 36100 kpa psi v 282 bar / 28200 kpa reference value at 1216 rpm and P0087 regulation of fuel pressure is lower that reference value 760 bar / 76000 kpa v 941 bar /...

her is diagnostic report

Hi guys,

Need some advise pls - this Boxer III 2008 model is driving me crazy...

Long story short had the terrible water ingress issue in the left loom (RHD) near the ABS that caused the BSi to short out and got damaged. All functions sjow but the CAN-lines inside and the immobiliser functionality is damaged. Got a 2nd hand BSi - same series no...

Mulling over dechroming my Obsidian Black 207cc, both interior and exterior.
I'm aware that matt black vent/centre console trim is available to replace the silver.
But... has anyone done this? What does the huge Peugeot front bumper badge look like in matt black?

I need to replace the centre part of the front grill.
This is the solid part that covers the towing eye bolt hole, has part number '7452HV' and is what I think Service Box refers to as the 'front bumper capping'.
Question is, is it possible to remove and replace this part without taking the entire front bumper off?

Hello. Before a month I got my Peugeot 2008 2024 model GT.
Yesterday I noticed a lot, A LOT spots with iron particles in the paint. Anyone found something like this?
What should I do? I want to ask a new car or my money back.

Well my little 206cc paid me back big time yesterday when i traded up for a 308cc 1.6hdi se. The 206cc smashed over half the asking price off the other car so I'm pleased .Photos will come in a few days.

I'm hoping this might ring a bell with someone. The vehicle is seemingly in good health, no fault codes, runs ok, clean exhaust under start up and usual driving. That is until the van starts an active regen at which point great clouds of billowing white smoke are emitted from the exhaust during acceleration. Once you get up to a steady speed on...

I have a problem with this error code P0238, read with my diagbox.
Car: Peugeot 307 1.6hdi 90hp year 2006
VF3**************[VIN obfuscated, can be read by forum staff]
I think the problem is the MAP sensor.
How can I check the MAP sensor? What should I follow on the live data in the diagbox to realize that the problem is the MAP sensor.
I tried to look for the diagnostic procedure in the...

Hi,
I have changed stem seals on my Peugeot 208 (EB2 engine).
When I was doing that I damaged one valve so I had to take the top of resulting in a bit bigger job :)

Now I am cleaning the valves and noticed the exhaust valves I cleaned looked like this.
I have given it a lap with paste but I do not want to do that too much.
The intake valves look...

Yesterday my 1.1 petrol 206 stated binging, the warning bing from the dashboard, and almost stalled a few times when dropping to tickover. This was towards the end of a short 6 mile inner city journey, stopped halfway to shop. there were only about four separate single bings but no warning lights on, temperature was halfway. At home I held the...

Hello, lads!

Any tips on how would I go about removing the front bumper lower skirt? It is attached to the front bumper by some clips/ rivets, not really sure so any advice would be much appreciated! Please find attached the uploaded attachment photos for reference. Many thanks!

Stelian

My wife has had a small coming together with a bollard and her RCZ as shown in the picture below:

IMG_20240406_193703.jpg

Is there a simple way to get behind that panel with a pusher either by removing the speaker or door latch or is it full interior strip to get to it that way?

Will it be simpler to use a dent puller and do it from outside?...

How much is it going to approx cost to have a towing bar fitted to a 205 and wired in ? Can it be done diy or is it better for a qualified mechanic to fit it and what about the legal paper work for the installation ?.

Hi. So the engine light has come back on. The lambda sensor has been changed twice (still within waranty time frame) exhaust box has been changed, catalytic converter has been checked, no issues there. ECU has been checked no issues there. Engine fault repair needed flashes on the dash. The car loses slight power sometimes & sometimes for a split...

The car is a Peogeot 207, 2008, 1.6l, petrol.

I am getting consistent error code P0328, which relates to the knock sensor. I am having difficulty identifying it. Haynes says on the back of the cylinder block and to remove the engine undershield, which suggests it is the bottom of the engine. I see a sensor there but not like the photo in Haynes....

Hello everyone! :)

This post is intended for tuning the good old BOSCH VE injection pump diesel fuel system, where we can share questions, experiences, and advice with each other.

We are building a 205 race car, which features an XUD9/TE engine with a Bosch fuel system.

My specific question is: what possibilities are there for tuning the...

Hello,
My Peugeot 508 SW GT (2016) 2 litre HDi appears to have a fault with the Start-Stop function. I had a new Battery Protection Module fitted by my dealer (best part of £400) which at least helped with some of the related minor problems - lots of error codes.
I also have a new Bosch battery - a proper one for the start stop function.
Even...

Hi,

I just installed a towbar and wiring harness in my car.

Now the manaual from the wiring harness says i have to place a 15A fuse in the engine compartment fuse box in slot 24.

Currently there is no fuse installed in the slot, I like to know what the exact function of the fuse is before i put any in, but i can't find any useful information on...

Left our new puppy in the car for a short while and returned to find she's had a good chew of the passanger front and rear belts. Stupidly left her on our other dogs tether with too much freedom.

Don't suppose anyone knows how to remove these so that I can send them off to have the webbing replaced?

Absolutely no idea how you get to the rear...

i have newly acquired a bipper yay me it smokes on start up, but once driven , goes , however comes back again when cold ( makes me think that an injector is leaking , Thus letting diesel build up in the exhaust system, ( showing white smoke until its burnt it off from the exhaust system )

i've taken the return feeds off ( i presume the nipples...

Hello,

I installed a new replacement catalytic converter with a FAP filter, and topped up the additive fluid in the tank. The car drove for several years without FAP.

After the installation we received the P1445 error, and we can't solve it.

The ECU was also replaced some years ago so it could be the wrong one.

Could you please send me the...

Good morning folks,
My 1998 106 1.1 has been having some idling and running issues. I believe I have found the source of the issue. The female connector plug for the throttle position sensor has a mangled socket which is causing the engine to stall. Unplugging the TPS exhibits the same symptom. Plugging it back it, the engine runs perfectly for a...

Hello wonderful people. It just so happens that one of you may save my life with your input here. I am out of ideas, quickly running out of money and have completely lost all love for cars after this. I’ll try to keep this brief but there is nothing brief about it unfortunately. Also please note: There are forum posts like this one but nothing...

I got a pair of front fog lights and a stalk for my phase 1 406, a bit nicer than looking at blanking panels

Fog lights and stalk are in place, the stalk even lights up the instrument cluster warning light for front fogs but no lights from the fog lights themselves yet. I think i need a relay

Ive tried to follow PSA wiring diagrams but im not...

Guys

Hope everyones doing well. Just had my peugeot 308 p5 airbag 2022 had replacement airbags. He also sent the module to get it reset crash data. However module arrived but he said he could not communicate with the airbag module.

Can anyone help me ? I need to reset the airbag module.

Hello all,

Ever since I purchased my Peugeot Partner Electric, I have had some intermittent problems with the Chademo fast charger. Sometimes it works, sometimes it doesnt and Sometimes, after it starts charging, it can randomly disconnect.
When I took it to the local Peugeot garage, they said that they couldnt see any fault codes :rolleyes:

I...

Hello everyone,I have a 2012 model 508 vehicle. After the installation of the PX5 android multimedia system, my start-stop system stopped working. During the installation, the car had entered economy mode and a fuse related to the sound system had blown. After replacing it, my sound system started working. I expected the start-stop system to work...

Hello, I am having a nightmare with my Boxer 3 Euro 6 2.0 BlueHDi Van and wonder if anyone here can help, please?

I’m new to the forums as a user but have been browsing for a while for advice, and I would like to thank you for all the information that has helped so far. I would be grateful if anyone could help with my issue below, as the garages...

Hello there can anyone help me and tell me if a icarsoft pc11. Or pc2 it might be called his decent to try start my Peugeot partner combi 2004 20hdi similar to Peugeot planet help please

The power steering pump not working but with the engine running if I tap the metal part of the pump casing with a mallet it starts working again

Hello.
Could someone advise me please on the programming injectors for the Peugeot 3008 2011 with ICarsoft CR PRO. The issue is that after I have renewed a new injector, I faced an issue with the Diagnostic tool: Application failed .
In fact, in the Injector menu I have two options:
1) Classification of injector.
2) Replacement of injector.

If I...

Please can anyone help my Peugeot partner 2004 20hdi stopped starting but sometimes but very rarely starts only got a cheap diagnostic tool and no codes cannot get it to garage cause won't start can anyone please give me a starting point to get it running

Guys

Caan anyone please help me to find out what is the part code for broken cables attached ? Its for 308 p5 2022 peugeot. Its the connector for Led headlight - the right side part no is 1801601

Hi, I have recently replaced a Peugeot 208 2013, bank 1 oxygen sensor with a universal crimp-type sensor to fit onto the original plug cabling.
The supplier didn't have access to the one with the correct plug, and it was due for MOT the next day after failing emissions the first time around, so I had to make do. It passed....but

Now I am...

In the office today(!), set off this morning and the lights come on, to be greeted with BING! and a message saying Automatic Headlamp Height Adjustment Faulty. Hmm. This has the swivelling HDI lamps, so place your bets as to whether it's a simple height sensor fault, or if it's a fault with one (or more!) of the ruinously expensive headlamp units!...

Is it advisable to put some sealer between the cam-housing and cam-cover gasket, perhaps Fel-pro Blue, Wellseal or similar?

Have just removed the rear cam-cover on my TU5JP4 engine as suspect slight oil leak from that gasket. Rubber seems a bit hard but maybe they are like that from new, nothing to compare it against.

Having only had my Peugeot for 6 weeks but having to use public charging several times, I'm a little disappointed at the rates I get.
According to the specifications, it's supposed to have a 100KW DC charging capability, however, I've never managed to get over 65KW rate, and that only for a couple of minutes before it drops down to ~34KW. This...